Blog Learning Centre
DIY Light Bundle for LEGO® Jango Fett™ #75408
It’s DIY all the way to bring your bounty hunter to life with our detailed DIY LEGO® lighting tutorial for the Jango Fett LEGO® helmet. You’ll be able to create a dramatic look using our customised component bundle from our DIY range. Whether you're a huge Star Wars fan or a master LEGO® builder looking to enhance your display, we can show you how to light your LEGO® Jango Fett helmet using our DIY tutorial suitable for any lighting skill level.
LEGO® Jango Fett™ Helmet #75408 DIY Light Bundle
What's included:
1 x Astro Light Large - Blue 15cm (4 Pack)
1 x Astro Spotlight Pack - Cool White (4 Pack)
1 x Tether 1x6 (2 Pack)
1 x Flux Belt 60cm
Total Price
€44.99 €64,96
In our tutorial, we’ll walk you through how to create an awesome display using a custom Jango Fett LEGO® light bundle, built with Light My Bricks DIY lighting components. Along the way we’ve got practical recommendations for clean cable routing, lighting placement for dramatic effect, and the hottest tips for your DIY LEGO® lighting setup.
Ideal for LEGO® lighting fans looking for:
- How to light the LEGO® Jango Fett helmet
- DIY LEGO® Star Wars lighting
- LEGO® helmet lighting tutorial
-
Custom lighting for LEGO® Star Wars helmets
Let’s jump in and get started customising your Jango Fett LEGO® helmet into a display-worthy centrepiece.
What you’ll need:
- Cool White Spotlight Pack
- Astro Large Blue 15cm Pack
- 1x6 Tether Pack
- Flux Belt 60cm
Step-by-Step Guide: How to Light Your LEGO® Jango Fett™ Helmet
Step 1: Removing parts
Remove the two panels from the back of the helmet.
Flip the build over and remove the tan plate from underneath.
Tip: Use a LEGO® brick separator to help with this.
Separate the helmet from the stand.
Step 2: Spotlight Assembly
Create your under-helmet spotlights with these steps:
Take a Cool White Astro 30cm Light.
Bend the LED back at a 90° angle, then thread the cable through an open stud plate.
Top it with an Astro Cap.
Grab two round plates with bar handles and a skeleton arm.
Attach the LED assembly to one of the plates.
Snap the skeleton arm onto the bar handle.
Attach the second plate to the other end of the skeleton arm.
For clean cable management:
- Slot the cable down behind the top plate’s bar handle.
- Loop it back around and thread it through the same position on the bottom plate.
Repeat this process to build a second spotlight.
Mount both spotlights underneath the front corners of the helmet stand as shown below.
Attach two stud jumpers underneath the stand, in the back corners as shown below.
Thread the cables up through the central channel of the stand.
Once the plugs appear on the other side, pull them through completely.
Next, add the flux belt following the exact same process for cable routing.
Hold the cables down and out of the way of studs and re-attach the helmet to the stand.
Step 4: Removing more parts
Remove all of the panels from both sides of the helmet.
Also remove the panels from the front.
Step 5: Lighting up the face
Thread an Astro Large Blue 15cm light through a 1x1 round plate with an open stud, just as you did earlier for the spotlight.
Mount this at the bottom of the centre panel that was removed from the front of the helmet.
Complete the following steps for each face plate:
Remove some pieces from the face plate as shown below.
Take another Astro Large Blue 15cm light and hold the light as shown below. Make sure the LED is facing away from you.
Replace the pieces that were removed in the same positions to hold the light in place.
Step 6: Reassembly & Cable Routing
Re-attach these assemblies to the main model.
Then go around and re-attach all of the side panels, making sure the cables route underneath the panels and between studs.
Step 7: Adding Power
Attach a 1x6 tether onto a Dock 6.
Plug each of your light cables into any of the center ports, and plug your Flux Belt into either Belt Port on the sides of the Dock.
Click the dock onto the underside of the helmet.
Step 8: Finish it off
Re-attach the two back panels of the helmet, with the cables pushed up and flat against the interior of the build.
Plug the USB-A end of your Flux Belt into a power source (such as a wall adapter or power bank). Your helmet is now fully powered and lit!
Shop Light My Bricks™ DIY Bundles & Create Your Own Iconic Masterpiece
Ready to design and customise your own Jango Fett LEGO® lighting setup? With just a few DIY LEGO® light packs from our DIY range and a bit of creativity, you can make your Star Wars LEGO® build shine bright. Find the full component list in one click and get started on your bounty-hunting masterpiece today.
Shop the Jango Fett Helmet DIY Lighting Pack now!
LEGO® Jango Fett™ Helmet #75408 DIY Light Bundle
What's included:
1 x Astro Light Large - Blue 15cm (4 Pack)
1 x Astro Spotlight Pack - Cool White (4 Pack)
1 x Tether 1x6 (2 Pack)
1 x Flux Belt 60cm
Total Price
€44.99 €64,96
You don’t need to be a lighting pro — you just need some LEGO® know-how and our DIY components to take your Jango Fett helmet to the next level.
Our Pro Tips for a Clean Setup & Maximum Impact
- Hide wire cables through Technic holes for a clean look
- Create spotlights for dramatic effect
- Route cables behind panels and between studs to keep neat and tidy
-
Take your time with reassembly because clean = professional!
Character with Light: Bringing Jango Fett to Life
Lighting isn’t just for show — it tells a story. Cool-toned spotlights enhance Jango’s iconic armour, while subtle lighting inside the helmet adds complimenting colour. Every detail is designed to amplify your LEGO® Jango Fett helmet build with immersive visuals and custom flair.
This Is Just the Beginning! Keep Lighting Your LEGO® Your Way
This tutorial is part of our DIY LEGO® lighting series for iconic sets, so stay tuned for more custom guides covering helmets, vehicles, and more — to help you explore how to install DIY LEGO® lights. Got your own story of your lighting masterpiece journey? Tag us with #lightmybricks and share your creation with our amazing LEGO® lighting community!
